H.M.S. Prince c.1670 -The Art Of Modification...Part Two

 As I sit here writing I can't help but to think how interesting my childhood was. I was adventurous and explorative. Always wanting to learn -whether from the classroom, the diverse community, or television. But the foundation of it all were my parents; primarily, my mother. In her was this immense wisdom that I later found in most women -and that ultimately put me over the top as a man, artist-craftsman, and father.

As such, I embraced history with an open mind -pushing away biases that was the pitfall to limited thinking. Instead, I absorbed every aspect of my profession down to the smallest details and embraced many, many cultures that helped it along...because in those cultures were missing pieces that made up what is viewed above -beauty.

In my early post on this subject I wrote about technique and staying in one's own lane. This principle I will continue to hammer home so that it will become evident (and fact) that we ALL have a purpose through the things we live and experience.

In the above image is the next stage is applied relative to taking plastic and simulating it to appear as wood. Yet, there are wood components in certain areas of the build.Al 

In this photo, natural wood components are seen -such as the interior deck props. These were fit in various locations to take on the wood cannons I made for the open gun ports. But prior to this I had to evaluate certain details and relocate them to their proper areas such as the deck furniture and bulkheads. The kit, though finely made, had issues which was unavoidable such as warping and mast displacement. Other factors included the bulkhead details such as adding to the carved pieces, removing windows and doors; and, substituting actual wood decks to take the eyebolts.  

The deadeye channels were no exception, they were completely replaced and knees which I hadn't  seen in any models. Knees were essential for strengthening the channels and lightening the stress when taking on the shrouds. At the fore channel such strengthening was mandatory when carrying the large stowed anchors.

Another missing element that I considered were the skids and/or fenders that were located amidship which ran down the side of the hull to the last wale at the waterline. These were very much part of the naval design -not just for British ships but for most seafaring nations. These skids and/or fenders prevented the boats from damaging the hull when being hoisted from and lowered into the water.

A closeup image showing the much notable skids/fenders. Also, notice the trunnels and planking about the topsides. This was done with a special pencil -one of the primary tools I use for both my models and dioramas. Every artistan have their arsenal of special tools needed to fit their line of work; and no two artists are alike because each use their tool(s) that are comfortable for his or her purpose. This is what makes work(s) 'original' and not a 'hard copy'. I encourage every novice artist/builder to explore materials and use them faithfully...because at the end of the day, the result will be yours. That advice you can take to the bank.

Research is beneficial at any level. The more study placed in a thing, expect better results!

I have invested countless hours in what I do and seldom keep logs. This current project is no exception. 

Usually I take my time (days or weeks) to scrutinize certain parts of the build before moving on to other areas. I will study other areas in preparation, but will refrain from touching anything until that particular space is finished -leaving no options to rework. This approach eliminate frustrations in the long run.

With the outside of the hull finished, I move on to the galleries. The windows would usually take a back seat until the lanterns are addressed...and yet, there are times when I would ignore the windows and move on to the interior work -such as the deck and cannons. The below images show the finished galleries.

The paints applied to this (and all my creations) are not straight from the jar; they are custom-mixed. Even the gold are applied in several variations -and gold leafed in certain areas for highlight. This process can take several weeks through experimentation.

To add better detail to gunports I work the lid ropes as shown in the following three images...

Next are the cannons which had to be scaled properly. The kit provided pieces that did not fit the overall appearance of the model. So, by trial and error, I made them from wood and secured them to wood platforms. This was followed by installing decks to cover the cannons and working up a template to make bulkheads and supporting deck furniture align correctly. Another set of photos support this below.

Viewing the image, the carriages and cannons are mounted below decks and the main deck is prefit to duplicate in wood. Also the plastic cannon/carriage are assessed to evaluate whether or not scaling is needed. The following photo show the conversion from plastic to wood on the quarter deck...

On this deck I relocated the grating as it is too close to the mizzen mast/slot. I noticed on various Prince models, this grating was omitted. It was inevitable to have these for dispersing smoke during cannon discharge.-especially since there were ten cannons within that enclosure.

In this image the main deck was also revised. It was here where I realized the scale of the guns were off relative to them clearing the bulwarks when being run in. Also the grating had to be slightly widened to support the boats without compromising the cannon. There was no room to place the grating that was supposedly behind the mainmast. In the plan drawn by noted British engineer Percival Marshall, no grating is shown.

Here is the scaled template I drafted to use throughout the build. The small markings on the side is the spacing of the shroud's ratlines in proportion to the crew members. There are more ratlines here than on conventional models

Another overview showing two separate templates for the build within the main deck waist. The lower template show the revised cannons in both run out and recoil position which has enough room to clear the bulwarks and gratings.

This conclude Part Two of the modification. There is much more to study before I move forward on this. However, from this assignment, I have come to learn more. I realize 'today' that Airfix models are a professional type model that is intend for those who are patient in the build for a museum type model of quality. There are many possibilities with this kit...and the plastic is of good quality to make changes that suit the builder.

Pieces are very small and to replicate them in another medium does require some skill. The drawback is missing pieces that can place a build 'on hold'...But for the experienced novice/professional, such parts can be customized.one can alter to be museum quality.

There is another factor that is overlooked with Airfix models; that is the scale. The company was precise in it, but the issue came up in debate on forums because builders couldn't match the scales based on the information given by the company. With a little investigative work I found that certain areas of each kit were either over-scaled or under-scaled. To alleviate that problem I picked two areas on the model that balanced in scale and reworked the entire model.

The two areas I studied were the steps, doors, and gun ports. I then made a crew figure template with additional deck furniture (to that scale) -giving me the precise measurements for all the fittings throughout the model. This procedure upgraded the Airfix kits to be a perfect 'one of a kind'.

There's not much more I can write on this blog segment except that we're in the midway process of the build. I appreciate your viewing this and will conclude the hull factor in 'Part Three' before moving on to the rigging. 

Fairwinds!